54 cat.8100h conductive polymer aluminum solid electrolytic capacitors pcr chip type, high reliability specifications temperature characteristics (max.impedance ratio) category temperature range rated voltage range rated capacitance range capacitance tolerance tangent of loss angle (tan ) esr ( 1) leakage current ( 2) performance characteristics item C 55 to +125c 16 to 80v 22 to 1000f 20% at 120hz, 20c less than or equal to the specified value at 120hz, 20c less than or equal to the specified value at 100khz, 20c after 2 minutes' application of rated voltage, leakage current is not more than 0.03cv or 3( a ), whichever is greater. z+125c / z+20c 1.25 (100khz) z C 55c / z+20c 1.25 endurance shelf life esr after endurance ( 1) damp heat (steady state) resistance to soldering heat marking the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 4000 hours at 125c. less than or equal to the specified value at 100khz, -40 c the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 85c, 85% rh. after soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. pre-heating shall be done at 150 to 200c and for 60 to 180 sec. the duration for over +230c temperature at capacitor surface shall not exceed 60 seconds. in case peak temperature is 260c or less, reflow soldering shall be two times maximum. measurement for solder temperature profile shall be made at the capacitor top and the terminal. navy blue print on the case top capacitance change tan leakage current ( 2) esr ( 1) within 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr ( 1) within 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value less than or equal to the initial specified value capacitance change tan leakage current ( 2) esr ( 1) within 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value less than or equal to the initial specified value high reliability, high voltage (to 80v). low esr, high ripple current. long life of 4000 hours at 125c. smd type : lead free reflow soldering condition at 260c peak complete correspondence. compliant to the rohs directive (2011/65/eu). esr after endurance at -40c. aec-q200 compliant. please contact us for details. 1 esr should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 conditioning : if any doubt arises, measure the leakage current after the voltage treatment of applying dc rated voltage continuously to the capacitor for 120 minutes at 105c. 3 initial value : the value before test of examination of resistance to soldering. p 1 c 2 r 3 1 4 v 5 1 6 5 7 1 8 m 9 c 10 l 11 1 12 g 13 s 14 configuration ta ping code size code capacitance tolerance ( 20%) rated capacitance ( 150f ) rated voltage ( 35v ) series name ty pe standard vi bration resistance code configuratio n l s type numbering system (example : 35v 150f) dimension table in next page. d l a b c e h size 8.0 6.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 7l 8.0 9.9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 10l 8.0 11 .9 9.0 8.3 8.3 3.2 0.8 to 1.1 8 12l 10.0 7.9 11 .0 10.3 10.3 4.6 0.8 to 1.1 10 8l 10.0 9.9 11 .0 10.3 10.3 4.6 0.8 to 1.1 10 10l 10.0 12.6 11 .0 10.3 10.3 4.6 0.8 to 1.1 10 12.7l (mm) code c v 16 d 20 e 25 v 35 h 50 j 63 k 80 v oltage d l a b c e h size 8.0 10.0 9.0 8.3 8.3 3.1 1.1 to 1. 5 8 10. 5l 10.0 10.0 11 .0 10.3 10.3 4.6 1.1 to 1. 5 10 1 0.5l 6.3 7.5 7.3 6.6 6.6 2.5 0.5 to 0. 8 6.3 8l 10.0 12.7 11 .0 10.3 10.3 4.6 1.1 to 1. 5 10 13.2l (mm) v ibration resistanc e standard pcr high capacitance long life assurance pcx after storing the capacitors under no load at 125c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20c, they shall meet the specified values for the endurance characteristics listed above. frequency coefficient of rated ripple current frequency coefficient 120hz 1khz 10khz 100khz or more 0.05 0.30 0.70 1.00 8 10l , 10 10l , 10 12.7l : the vibration structure-resistant product is also available upon request, please ask for details. c r 1 5 0 v 3 3 1 h 0. 3 m ax. d 0.5 b 0.2 a 0.2 c 0.2 0. 5 m ax. e l series voltage (v:35v) plastic platform lot no. capacitance negative negative positive positive +0.1 - 0 .4 standard vibration resistance h 0.3 max. d 0.5 b 0.2 a 0.2 c0.2 0.5 max. e l 0.5 plastic platform aid electrode c r 1 5 0 v 3 3 1 series voltage (v:35v) lot no. capacitance dimensions
55 cat.8100h conductive polymer aluminum solid electrolytic capacitors pcr dimensions rated voltage (v)(code) surge voltage (v) 1500 3400 2200 3800 3200 4300 1200 3300 2100 3500 3100 4200 1200 3200 2100 3300 3100 4100 1200 3100 2100 3300 3100 3900 1300 2900 1900 2900 3000 3500 1100 2700 1800 2900 2800 3000 1400 1600 1700 2100 60 34 64 32 38 26 78 38 66 36 40 28 82 40 66 38 40 30 88 44 66 42 40 32 90 52 84 50 50 38 96 56 94 54 56 48 76 70 66 56 30 17 32 16 19 13 39 19 33 18 20 14 41 20 33 19 20 15 44 22 33 21 20 16 45 26 42 25 25 19 48 28 47 27 28 24 38 35 33 28 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 8 7 8 10 10 8 8 12 10 10 10 12.7 8 7 8 10 10 8 8 12 10 10 10 12.7 8 7 8 10 10 8 8 12 10 10 10 12.7 8 7 8 10 10 8 8 12 10 10 10 12.7 220 470 470 560 680 1000 150 330 330 470 560 680 100 220 220 270 330 470 68 150 150 220 270 330 20 16 (1c) 25 20 (1d) 31 25 (1e) 43 35 (1v) pcr1c221mcl1gs pcr1c471mcl6gs pcr1c471mcl1gs pcr1c561mcl1gs pcr1c681mcl1gs pcr1c102mcl1gs pcr1d151mcl1gs pcr1d331mcl6gs pcr1d331mcl1gs pcr1d471mcl1gs pcr1d561mcl1gs pcr1d681mcl1gs pcr1e101mcl1gs pcr1e221mcl6gs pcr1e221mcl1gs pcr1e271mcl1gs pcr1e331mcl1gs pcr1e471mcl1gs pcr1v680mcl1gs pcr1v151mcl6gs pcr1v151mcl1gs pcr1v221mcl1gs pcr1v271mcl1gs pcr1v331mcl1gs pcr1h390mcl1gs pcr1h820mcl6gs pcr1h820mcl1gs pcr1h121mcl2gs pcr1h121mcl1gs pcr1h181mcl1gs pcr1j220mcl1gs PCR1J390MCL1GS pcr1j470mcl1gs pcr1j560mcl1gs pcr1j680mcl1gs pcr1j101mcl1gs pcr1k270mcl1gs pcr1k390mcl1gs pcr1k470mcl1gs pcr1k680mcl1gs rated capacitance (f) case size d l (mm) tan part number low temp. esr after endurance (m ) (-40c / 100khz) rated ripple (marms) (125c / 100khz) initial esr (m ) (20c / 100khz) 39 82 82 120 120 180 22 39 47 56 68 100 27 39 47 68 63 50 (1h) 79 63 (1j) 100 80 (1k) 8 7 8 10 10 8 8 12 10 10 10 12.7 8 7 8 10 10 8 8 12 10 10 10 12.7 8 10 8 12 10 10 10 12.7 rated ripple current (marms) at 125c 100khz no marked, 1 will be put at 12th digit of type numbering system. : in this case, 2 will be put at 12th digit of type numbering system. : in this case, 6 will be put at 12th digit of type numbering system. taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please refer to page 3 for the minimum order quantity.
|
